Welcome to DU! The truly grassroots left-of-center political community where regular people, not algorithms, drive the discussions and set the standards. Join the community: Create a free account Support DU (and get rid of ads!): Become a Star Member Latest Breaking News Editorials & Other Articles General Discussion The DU Lounge All Forums Issue Forums Culture Forums Alliance Forums Region Forums Support Forums Help & Search

DIY & Home Improvement

Beartracks

(14,778 posts)

36. Would Liquid Wrench work against a thread glue like Loctite?

Reply to KY_EnviroGuy (Reply #30)

Sat Jul 4, 2026, 05:40 PM

5 hrs ago

Edit history

Please sign in to view edit histories.

Recommendations

0 members have recommended this reply (displayed in chronological order):

39 replies

= new reply since forum marked as read

Highlight:

"Factory-tight" bolt in my washer: Won't budge! [View all] Beartracks 9 hrs ago OP

WD-40 Ponietz 9 hrs ago #1

lubrication Kali 9 hrs ago #2

Do you have a torch? Nittersing 9 hrs ago #3

Don't have any suggestion, but UpInArms 9 hrs ago #4

Yep, I did that so I'd know what I was getting into. However, of course... Beartracks 8 hrs ago #19

Might be time to get on the LG website... GiqueCee 8 hrs ago #28

According to what I found drray23 9 hrs ago #5

This message was self-deleted by its author taxi 8 hrs ago #17

I did try whacking it with a pipe wrench, since my hammer wasn't readily available. Beartracks 8 hrs ago #21

This message was self-deleted by its author taxi 8 hrs ago #29

So smack the wrench handle BETWEEN my hand and the end that's on bolt? Beartracks 5 hrs ago #37

This message was self-deleted by its author taxi 5 hrs ago #38

Whaaat? Although, this tracks with my experience. The bolt acts like it's fused to the rotor metal. Beartracks 8 hrs ago #18

Some people have suggested PB Blaster. Would that work on glue, or is it only for rust/gunk? Beartracks 8 hrs ago #22

If you have a length of pvc pipe that you can slip on the ratchet handle that will add leverage. Good luck! Floyd R. Turbo 9 hrs ago #6

I like the idea of sliding the rachet handle into a long pipe. dem4decades 9 hrs ago #7

You can dry heating it up with a blow dryer for a bit. Shambala 9 hrs ago #8

Same for me Dragonfly64 7 hrs ago #32

Lots of WD40? irisblue 9 hrs ago #9

How big is this bolt? House of Roberts 8 hrs ago #10

17 mm Beartracks 8 hrs ago #15

Try tapping the bolt head with a hammer... LuckyCharms 8 hrs ago #11

Interesting point about 6-pt vs 12-pt Beartracks 8 hrs ago #13

I don't know if you can get your hands on a 6 point today... LuckyCharms 8 hrs ago #16

Thanks! Timing is everything, right? Beartracks 8 hrs ago #20

Other things to look at... Flash953 8 hrs ago #12

Motor is fine. It's an LG. I'm just needing to replace the sensor. Beartracks 8 hrs ago #14

Could it be a left-hand thread? Some bolts are opposite to avoid loosening. Norrrm 8 hrs ago #23

Good point... GiqueCee 8 hrs ago #25

Not according to Dr. Google (YouTube DIYers, in this case), but I will try that. Beartracks 8 hrs ago #26

Is it reverse threaded? SheltieLover 8 hrs ago #24

Not according to Dr. Google (YouTube DIYers, in this case), but I will try that. Beartracks 8 hrs ago #27

Pls let us know. SheltieLover 8 hrs ago #31

They may have used something like Loctite on it. KY_EnviroGuy 8 hrs ago #30

Would Liquid Wrench work against a thread glue like Loctite? Beartracks 5 hrs ago #36

Straight from the horse's mouth..... KY_EnviroGuy 1 hr ago #39

heat is the trick for locktite Liber T. 6 hrs ago #33

WD-40 is not a penetrant or lubricant Liber T. 6 hrs ago #34

impact wrench The Wizard 6 hrs ago #35